Being around a construction site you will hear some terminology that is unfamiliar to you. We have listed just about any term you might hear in a simple quick reference guide for you.

A B C D E F G H I J K L M N O P Q R S T U V W Y Z

A/C- An abbreviation for air  conditioner or air conditioning.

A/C Condenser- The outside fan  unit of the Air Conditioning system. It removes the heat from the freon  gas and "turns" the gas back into a liquid and pumps the liquid back to  the coil in the furnace.

A/C Disconnect- The main  electrical ON-OFF switch near the A/C Condenser.

Aerator- The round screened  screw-on tip of a sink spout. It mixes water and air for a smooth flow.

Aggregate- A mixture of sand and stone and a major component of concrete.

Air space - The area between  insulation facing and interior of exterior wall coverings. Normally a 1" air gap.

Allowance(s) - A sum of money  set aside in the construction contract for items which have not been  selected and specified in the construction contract. For example,  selection of tile as a flooring may require an allowance for an  underlayment material, or an electrical allowance which sets aside an  amount of money to be spent on electrical fixtures.

Amortization - A payment plan by which a loan is reduced through monthly payments of principal and  interest.

Anchor bolts- Bolts to secure a  wooden sill plate to concrete , or masonry floor or wall.

Annual Percentage Rate (APR)-  Annual cost of credit over the life of a loan, including interest,  service charges, points, loan fees, mortgage insurance, and other items.

Appraisal An expert valuation of property.

Apron- A trim board that is  installed beneath a window sill

Architect - One who has  completed a course of study in building and design, and is licensed by  the state as an architect. One who draws up plans.

Area wells- Corrugated metal or  concrete barrier walls installed around a basement window to hold back  the earth

Assessment - A tax levied on a  property, or a value placed on the worth of a property.

Assumption - Allows a buyer to  assume responsibility for an existing loan instead of getting a new  loan.

Astragal- A molding, attached to one of a pair of swinging double doors, against which the other door  strikes.

Attic access- An opening that is placed in the drywalled ceiling of a home providing access to the  attic.

Attic Ventilators- In houses,  screened openings provided to ventilate an attic space.

Back To Top

Back Charge- Billings for work  performed or costs incurred by one party that, in accordance with the  agreement, should have been performed or incurred by the party to whom  billed. Owners bill back charges to general contractors, and general  contractors bill back charges to subcontractors. Examples of back  charges include charges for cleanup work or to repair something damaged  by another subcontractor, such as a tub chip or broken window.

Backfill- The replacement of  excavated earth into a trench around or against a basement /crawl space  foundationwall.

Backing- Frame lumber installed  between the wall studs to give additional support for drywall or an  interior trim related item, such as handrail brackets, cabinets, and  towel bars. In this way, items are screwed and mounted into solid wood  rather than weak drywall that may allow the item to break loose from the wall. Carpet backing holds the pile fabric in place.

Backout- Work the framing  contractor does after the mechanical subcontractors  (Heating-Plumbing-Electrical) finish their phase of work at the Rough  (before insulation) stage to get the home ready for a municipal frame  inspection. Generally, the framing contractor repairs anything disturbed by others and completes all framing necessary to pass a Rough Frame  Inspection.

Ballast- A transformer that  steps up the voltage in a florescent lamp.

Balloon - A loan that has a  series of monthly payments with the remaining balance due in a large  lump sum payment at the end.

Balloon framed wall- Framed  walls (generally over 10' tall) that run the entire vertical length from the floor sill plate to the roof. This is done to eliminate the need  for a gable end truss.

Balusters- Vertical members in a railing used between a top rail and bottom rail or the stair treads.  Sometimes referred to as 'pickets' or 'spindles'.

Balustrade- The rail, posts and  vertical balusters along the edge of a stairway or elevated walkway.

Barge- Horizontal beam rafter  that supports shorter rafters.

Barge board- A decorative board  covering the projecting rafter (fly rafter) of the gable end. At the  cornice, this member is a fascia board.

Base or baseboard- A trim board  placed against the wall around the room next to the floor.

Basement window inserts- The  window frame and glass unit that is installed in the window buck.

Base shoe- Molding used next to  the floor on interior base board. Sometimes called a carpet strip.

Bat - A half-brick.

Batt - A section of fiber-glass  or rock-wool insulation measuring 15 or 23 inches wide by four to eight  feet long and various thickness'.  Sometimes "faced" (meaning to have a paper covering on one side) or "unfaced" (without paper).

Batten- Narrow strips of wood  used to cover joints or as decorative vertical members over plywood or  wide boards.

Bay window- Any window space  projecting outward from the walls of a building, either square or  polygonal in plan.

Beam- A structural member  transversely supporting a load. A structural member carrying building  loads (weight) from one support to another. Sometimes called a "girder".

Bearing partition- A partition  that supports any vertical load in addition to its own weight.

Bearing point- A point where a  bearing or structural weight is concentrated and transferred to the  foundation

Bearing wall- A wall that  supports any vertical load in addition to its own weight.

Bearing header- (a) A beam  placed perpendicular to joists and to which joists are nailed in framing for a chimney, stairway, or other opening. (b) A wood lintel. (c) The  horizontal structural member over an opening (for example over a door or window).

Bedrock- A subsurface layer of  earth that is suitable to support a structure.

Bid- A formal offer by a  contractor, in accordance with specifications for a project, to do all  or a phase of the work at a certain price in accordance with the terms  and conditions stated in the offer.

Bid bond- A bond issued by a  surety on behalf of a contractor that provides assurance to the  recipient of the contractor's bid that, if the bid is accepted, the  contractor will execute a contract and provide a performance bond. Under the bond, the surety is obligated to pay the recipient of the bid the  difference between the contractor's bid and the bid of the next lowest  responsible bidder if the bid is accepted and the contractor fails to  execute a contract or to provide a performance bond.

Bid security Funds or a bid bond submitted with a bid as a guarantee to the recipient of the bid that  the contractor, if awarded the contract, will execute the contract in  accordance with the bidding requirements of the contract documents.

Bid shopping- A practice by  which contractors, both before and after their bids are submitted,  attempt to obtain prices from potential subcontractors and material  suppliers that are lower than the contractors' original estimates on  which their bids are based, or after a contract is awarded, seek to  induce subcontractors to reduce the subcontract price included in the  bid.

Bidding requirements- The  procedures and conditions for the submission of bids. The requirements  are included ion documents, such as the notice to bidders,  advertisements for bids, instructions to bidders, invitations to bid,  and sample bid forms.

Bifold door- Doors that are  hinged in the middle for opening in a smaller area than standard swing  doors. Often used for closet doors.

Binder- A receipt for a deposit  to secure the right to purchase a home at an agreed terms by a buyer and seller.

Bipass doors- Doors that slide  by each other and commonly used as closet doors.

Blankets- Fiber-glass or  rock-wool insulation that comes in long rolls 15 or 23 inches wide.

Blocked (door blocking)- Wood  shims used between the door frame and the vertical structural wall  framing members.

Blocked (rafters)- Short "2 by  4's" used to keep rafters from twisting, and installed at the ends and  at mid-span.

Blocking- Small wood pieces to  brace framing members or to provide a nailing base for gypsum board or  paneling.

Block out- To install a box or  barrier within a foundation wall to prevent the concrete from entering  an area. For example, foundation walls are sometimes "blocked" in order  for mechanical pipes to pass through the wall, to install a crawl space  door, and to depress the concrete at a garage door location.

Blow insulation- Fiber  insulation in loose form and used to insulate attics and existing walls  where framing members are not exposed.

Blue print(s) - A type of  copying method often used for architectural drawings. Usually used to  describe the drawing of a structure which is prepared by an architect or designer for the purpose of design and planning, estimating, securing  permits and actual construction.

Blue stake- Another phrase for  Utility Notification. This is when a utility company (telephone, gas,  electric, cable TV, sewer and water, etc) comes to the job site and  locates and spray paints the ground and/or installs little flags to show where their service is located underground.

Board foot- A unit of measure  for lumber equal to 1 inch thick by 12 inches wide by 12 inches long.  Examples: 1" x 12" x 16' = 16 board feet, 2" x 12" x 16' = 32 board feet

Bond or bonding - An amount of  money (usually $5,000-$10,000) which must be on deposit with a  governmental agency in order to secure a contractor's license. The bond  may be used to pay for the unpaid bills or disputed work of the  contractor. Not to be confused with a 'performance bond'. Such  bonds are rarely used in residential construction, they are an insurance policy which guarantees proper completion of a project.

Boom- A truck used to hoist  heavy material up and into place. To put trusses on a home or to set a  heavy beam into place.

Bottom chord - The lower or  bottom horizontal member of a truss.

Bottom plate- The "2 by 4's or  6's" that lay on the subfloor upon which the vertical studs are  installed. Also called the 'sole plate'.

Brace- An inclined piece of  framing lumber applied to wall or floor to strengthen the structure.  Often used on walls as temporary bracing until framing has been  completed.

Breaker panel- The electrical  box that distributes electric power entering the home to each branch  circuit (each plug and switch) and composed of circuit breakers.

Brick ledge- Part of the  foundation wall where brick (veneer) will rest.

Brick lintel- The metal angle  iron that brick rests on, especially above a window, door, or other  opening.

Brick mold-Trim used around an  exterior door jamb that siding butts to.

Brick tie- A small, corrugated  metal strip @ 1" X 6"- 8" long nailed to wall sheeting or studs. They  are inserted into the grout mortar joint of the veneer brick, and holds  the veneer wall to the sheeted wall behind it.

Brick veneer- A vertical facing  of brick laid against and fastened to sheathing of a framed wall or tile wall construction.

Bridging- Small wood or metal  members that are inserted in a diagonal position between the floor  joists or rafters at mid-span for the purpose of bracing the  joists/rafters & spreading the load.

Buck- Often used in reference to rough frame opening members. Door bucks used in reference to metal door frame. See Window Bucks

Builder's Risk Insurance-  Insurance coverage on a construction project during construction,  including extended coverage that may be added for the contract for the  customer's protections.

Building codes-  Community  ordinances governing the manner in which a home may be constructed or  modified.

Building insurance- Insurance  covering the structure of the building.

Building paper- A general term  for papers, felts, and similar sheet materials used in buildings without reference to their properties or uses. Generally comes in long rolls.

Built-up roof- A roofing  composed of three to five layers of asphalt felt laminated with coal  tar, pitch, or asphalt. The top is finished with crushed slag or gravel. Generally used on flat or low-pitched roofs.

Bull nose (drywall)- Rounded  drywall corners.

Bundle - A package of shingles.  Normally, there are 3 bundles per square and 27 shingles per bundle.

Butt edge- The lower edge of the shingle tabs.

Butt hinge- The most common  type. One leaf attaches to the door's edge, the other to its jamb.

Butt joint- The junction where  the ends of two timbers meet, and also where sheets of drywall meet on  the 4 foot edge. To place materials end-to-end or end-to-edge without  overlapping.

Buy down- A subsidy (usually  paid by a builder or developer) to reduce monthly payments on a  mortgage.

By fold door- Doors that are  hinged in the middle for opening in a smaller area than standard swing  doors. Often used for closet doors.

By pass doors- Doors that slide  by each other and commonly used as closet doors.

Back To Top

CO- An abbreviation for "Certificate of Occupancy". This certificate is issued by the local municipality and is required before anyone can occupy and live within the home. It  is issued only after the local municipality has made all inspections and all monies and fees have been paid.

Caisson- A 10" or 12" diameter  hole drilled into the earth and embedded into bedrock 3 - 4 feet. The  structural support for a type of foundation wall, porch, patio,  monopost, or other structure. Two or more "sticks" of reinforcing bars  (rebar) are inserted into and run the full length of the hole and  concrete is poured into the caisson hole

Cantilever- An overhang. Where  one floor extends beyond and over a foundation wall. For example at a  fireplace location or bay window cantilever. Normally, not extending  over 2 feet.

Cantilevered void- Foundation  void material used in unusually expansive soils conditions. This void is "trapezoid" shaped and has vertical sides of 6" and 4" respectively.

Cap- The upper member of a  column, pilaster, door cornice, molding, or fireplace.

Cap flashing- The portion of the flashing attached to a vertical surface to prevent water from migrating behind the base flashing.

Capital- The principal part of a loan, i.e. the original amount borrowed.

Capital and interest- A  repayment loan and the most conventional form of home loan. The borrower pays an amount each month to cover the amount borrowed (or capital or  principal) plus the interest charged on capital.

Capped rate- The mortgage  interest rate will not exceed a specified value during a certain period  of time, but it will fluctuate up and down below that level.

Casement- Frames of wood or  metal enclosing part (or all) of a window sash. May be opened by means  of hinges affixed to the vertical edges.

Casement Window- A window with  hinges on one of the vertical sides and swings open like a normal door

Casing- Wood trim molding  installed around a door or window opening.

Caulking- (1) A flexible  material used to seal a gap between two surfaces e.g. between pieces of  siding or the corners in tub walls. (2) To fill a joint with mastic or  asphalt plastic cement to prevent leaks.

CCA (Chromated Copper Arsenate)- A pesticide that is forced into wood under high pressure to protect it  from termites, other wood boring insects, and decay caused by fungus

Celotex - Black fibrous board that is used as exterior sheething.

Ceiling joist- One of a series  of parallel framing members used to support ceiling loads and supported  in turn by larger beams, girders or bearing walls. Also called roof  joists.

Cement- The gray powder that is  the "glue" in concrete. Portland cement. Also, any adhesive.

Ceramic tile- A man-made or  machine-made clay tile used to finish a floor or wall. Generally used in bathtub and shower enclosures and on counter tops.

CFM (cubic feet per minute)- A  rating that expresses the amount of air a blower or fan can move. The  volume of air (measured in cubic feet) that can pass through an opening  in one minute.

Chair rail- Interior trim  material installed about 3-4 feet up the wall, horizontally.

Chalk line- A line made by  snapping a taut string or cord dusted with chalk. Used for alignment  purposes.

Change order- A written document which modifies the plans and specifications and/or the price of the  construction Contract.

Chase- A framed enclosed space  around a flue pipe or a channel in a wall, or through a ceiling for  something to lie in or pass through.

Chink- To install fiberglass  insulation around all exterior door and window frames, wall corners, and small gaps in the exterior wall.

Chip Board- A manufactured wood  panel made out of 1"- 2" wood chips and glue. Often used as a substitute for plywood in the exterior wall and roof sheathing. Also called OSB  (Oriented Strand Board) or wafer board.

Circuit- The path of electrical  flow from a power source through an outlet and back to ground.

Circuit Breaker- A device which  looks like a switch and is usually located inside the electrical breaker panel or circuit breaker box. It is designed to (1) shut of the power  to portions or all of the house and (2) to limit the amount of power  flowing through a circuit (measured in amperes). 110 volt household  circuits require a fuse or circuit breaker with a rating of 15 or a  maximum of 20 amps. 220 volt circuits may be designed for higher  amperage loads e.g. a hot water heater may be designed for a 30 amp load and would therefore need a 30 amp fuse or breaker.

Class "A"- Optimum fire rating  issued by Underwriter's Laboratories on roofing. The building codes in  some areas require this type of roofing for fire safety.

Class "C"- Minimum fire rating  issued by the Underwriters' Laboratories for roofing materials.

Clean out- An opening providing  access to a drain line. Closed with a threaded plug.

Clip ties- Sharp, cut metal  wires that protrude out of a concrete foundation wall (that at one time  held the foundation form panels in place).

Cold air return- The ductwork  (and related grills) that carries room air back to the furnace for  re-heating.

Collar- Preformed flange placed  over a vent pipe to seal the roofing above the vent pipe opening. Also  called a vent sleeve.

Collar beam- Nominal 1- or  2-inch-thick members connecting opposite roof rafters. They serve to  stiffen the roof structure.

Column- A vertical structural  compression member which supports loads.

Combustion air- The duct work  installed to bring fresh, outside air to the furnace and/or hot water  heater. Normally 2 separate supplies of air are brought in: One high and One low.

Combustion chamber- The part of a boiler, furnace or woodstove where the burn occurs; normally lined with firebrick or molded or sprayed insulation.

Compression web- A member of a  truss system which connects the bottom and top chords and which  provides downward support.

Compressor- A mechanical device  that pressurizes a gas in order to turn it into a liquid, thereby  allowing heat to be removed or added. A compressor is the main component of conventional heat pumps and air conditioners. In an air conditioning system, the compressor normally sits outside and has a large fan (to  remove heat).

Concrete- The mixture of  Portland cement, sand, gravel, and water. Used to make garage and  basement floors, sidewalks, patios, foundation walls, etc. It is  commonly reinforced with steel rods (rebar) or wire screening (mesh).

Concrete block - A hollow  concrete 'brick' often 8" x 8" x 16" in size.

Concrete board - A panel made  out of concrete and fiberglass usually used as a tile backing material.

Condensation- Beads or drops of  water (and frequently frost in extremely cold weather) that accumulate  on the inside of the exterior covering of a building. Use of louvers or  attic ventilators will reduce moisture condensation in attics. A vapor  barrier under the gypsum lath or dry wall on exposed walls will reduce  condensation.

Condensing unit - The outdoor  component of a cooling system. It includes a compressor and condensing  coil designed to give off heat.

Conditions, Convenants, and  Restrictions (CC and Rs) - The standards that define how a property  may be used and the protections the developer makes for the benefit of  all owners in a subdivision.

Conduction- The direct transfer  of heat energy through a material.

Conductivity- The rate at which  heat is transmitted through a material.

Conduit, electrical- A pipe,  usually metal, in which wire is installed.

Construction Contract - A legal  document which specifies the what-when-where-how-how much and by whom in a construction project. A good construction contract will include:

				1.	The contractors registration  number.
				2.	A statement of work quality such  as 'Standard Practices of the Trades' or 'according to Manufacturers  Specifications'.
				3.	A set of Blue Prints or Plans
				4.	A construction timetable  including starting and completion dates.
				5.	A set of Specifications
				6.	A Fixed Price for the work, or a  Time and Materials formula.
				7.	A Payment Schedule.
				8.	Any Allowances.
				9.	A clause which outlines how any  disputes will be resolved.
				10.	A written Warrantee.

Construction drywall- A  type of construction in which the interior wall finish is applied in a  dry condition, generally in the form of sheet materials or wood paneling as contrasted to plaster.

Construction, frame- A type of  construction in which the structural components are wood or depend upon a wood frame for support.

Continuity tester- A device  that tells whether a circuit is capable of carrying electricity.

Contractor- A company licensed  to perform certain types of construction activities. In most states, the generals contractor's license and some specialty contractor's licenses  don't require of compliance with bonding, workmen's compensation and  similar regulations. Some of the specialty contractor licenses involve  extensive training, testing and/or insurance requirements. There are  various types of contractors:

			General contractor -  responsible for the execution, supervision and overall coordination of a project and may also perform some of the individual construction tasks. Most general contractors are not licensed to perform all specialty  trades and must hire specialty contractors for such tasks, e.g.  electrical, plumbing.
			Remodeling contractor - a general contractor who specializes in remodeling work.
			Specialty contractor -  licensed to perform a specialty task e.g. electrical, side sewer,  asbestos abatement.
			Sub contractor - a  general or specialty contractor who works for another general  contractor.

Control joint- Tooled,  straight grooves made on concrete floors to "control" where the concrete should crack

Convection- Currents created  by heating air, which then rises and pulls cooler air behind it. Also  see radiation.

Conventional loan A mortgage  loan not insured by a government agency (such as FHA or VA)

Convertibility The ability to  change a loan from an adjustable rate schedule to a fixed rate schedule.

Cooling load- The amount of  cooling required to keep a building at a specified temperature during  the summer, usually 78° F, regardless of outside temperature.

Coped- Removing the top and  bottom flange of the end(s) of a metal I-beam. This is done to permit it to fit within, and bolted to, the web of another I-beam in a "T"  arrangement

Coped joint- Cutting and  fitting woodwork to an irregular surface.

Corbel- The triangular,  decorative and supporting member that holds a mantel or horizontal  shelf.

Corner bead- A strip of formed sheet metal placed on outside corners of drywall before applying  drywall 'mud'.

Corner boards- Used as trim  for the external corners of a house or other frame structure against  which the ends of the siding are finished.

Corner braces- Diagonal braces at the corners of the framed structure designed to stiffen and  strengthen the wall.

Cornice- Overhang of a pitched roof , usually consisting of a fascia board, a soffit and appropriate  trim moldings.

Counter flashing- A metal  flashing usually used on chimneys at the roofline to cover shingle  flashing and used to prevent moisture entry.

Counterfort- A foundation wall section that strengthens (and generally perpendicular to) a long  section of foundation wall

Course- A row of shingles or  roll roofing running the length of the roof. Parallel layers of building materials such as bricks, or siding laid up horizontally.

Cove molding- A molding with a concave face used as trim or to finish interior corners.

Crawl space- A shallow space  below the living quarters of a house, normally enclosed by the  foundation wall and having a dirt floor.

Credit rating- A report  ordered by a lender from a credit agency to determine a borrower's  credit habits.

Cricket- A second roof built  on top of the primary roof to increase the slope of the roof or valley. A saddle-shaped, peaked construction connecting a sloping roof with a  chimney. Designed to encourage water drainage away from the chimney  joint.

Cripple- Short vertical "2 by  4's or 6's" frame lumber installed above a window or door.

Cross bridging- Diagonal  bracing between adjacent floor joists, placed near the center of the  joist span to prevent joists from twisting.

Cross Tee- Short metal "T" beam used in suspended ceiling systems to bridge the spaces between the main beams.

Crown molding- A molding used  on cornice or wherever an interior angle is to be covered, especially at the roof and wall corner.

Culvert- Round, corrugated  drain pipe (normally 15" or 18" in diameter) that is installed beneath a driveway and parallel to and near the street.

Cupping- A type of warping  that causes boards to curl up at their edges.

Curb- The short elevation of  an exterior wall above the deck of a roof. Normally a 2 by 6 box (on the roof) on which a skylight is attached.

Curb stop- Normally a cast  iron pipe with a lid (@ 5" in diameter) that is placed vertically into  the ground, situated near the water tap in the yard, and where a water  cut-off valve to the home is located (underground). A long pole with a  special end is inserted into the curb stop to turn off/on the water.

Cut-in brace- Nominal  2-inch-thick members, usually 2 by 4's, cut in between each stud  diagonally.

Back To Top

Dado- A groove cut into a  board or panel intended to receive the edge of a connecting board or  panel.

Damper- A metal "door" placed  within the fireplace chimney. Normally closed when the fireplace is not  in use.

Dampproofing- The black, tar  like waterproofing material applied to the exterior of a foundation  wall.

Daylight- The end of a pipe  (the terminal end) that is not attached to anything.

Dead bolt- An exterior  security lock installed on exterior entry doors that can be activated  only with a key or thumb-turn. Unlike a latch, which has a beveled  tongue, dead bolts have square ends.

Dead light- The fixed,  non-operable window section of a window unit.

Deck, decked- To install the  plywood or wafer board sheeting on the floor joists, rafters, or  trusses.

Dedicated circuit- An  electrical circuit that serves only one appliance (ie, dishwasher) or a  series of electric heaters or smoke detectors.

Default- Breach of a mortgage  contract (not making the required payments).

De-humidistat- A control  mechanism used to operate a mechanical ventilation system based upon the relative humidity in the home.

Delamination- Separation of  the plies in a panel due to failure of the adhesive.  Usually caused by excessive moisture.

Disconnect- A large (generally 20 Amp) electrical ON-OFF switch.

Discount rate- A mortgage  interest rate that is lower than the current rate for a certain period  of time, e.g. 2.00% below variable rate for 2 years.

Doorjamb, interior- The  surrounding case into which and out of which a door closes and opens. It consists of two upright pieces, called side jambs, and a horizontal  head jamb. These 3 jambs have the "door stop" installed on them.

Door operator- An automatic  garage door opener.

Door stop- The wooden style  that the door slab will rest upon when it's in a closed position.

Dormer- An opening in a  sloping roof, the framing of which projects out to form a vertical wall  suitable for windows or other openings.

Double glass- Window or door  in which two panes of glass are used with a sealed air space between.   Also known as Insulating Glass.

Double hung window- A window  with two vertically sliding sashes, both of which can move up and down.

Down payment- The difference  between the sales price and the mortgage amount. A downpayment is  usually paid at closing.

Downspout- A pipe, usually of  metal, for carrying rainwater down from the roof's horizontal gutters.

Drain tile- A perforated,  corrugated plastic pipe laid at the bottom of the foundation wall and  used to drain excess water away from the foundation. It prevents ground  water from seeping through the foundation wall. Sometimes called  perimeter drain.

Draw- The amount of progress  billings on a contract that is currently available to a contractor under a contract with a fixed payment schedule.

Drip- (a) A member of a  cornice or other horizontal exterior finish course that has a projection beyond the other parts for throwing off water.(b) A groove in the  underside of a sill or drip cap to cause water to drop off on the outer  edge instead of drawing back and running down the face of the building.

Drip cap- A molding or metal  flashing placed on the exterior topside of a door or window frame to  cause water to drip beyond the outside of the frame.

Dry in- To install the black  roofing felt (tar paper) on the roof.

Drywall (or Gypsum Wallboard  (GWB), Sheet rock or Plasterboard)- Wall board or gypsum- A  manufactured panel made out of gypsum plaster and encased in a thin  cardboard. Usually 1/2" thick and 4' x 8' or 4' x 12' in size. The  panels are nailed or screwed onto the framing and the joints are taped  and covered with a 'joint compound'. 'Green board' type drywall has a  greater resistance to moisture than regular (white) plasterboard and is  used in bathrooms and other "wet areas".

Ducts- The heating system.  Usually round or rectangular metal pipes installed for distributing warm (or cold) air from the furnace to rooms in the home.  Also a tunnel  made of galvanized metal or rigid fiberglass, which carries air from the heater or ventilation opening to the rooms in a building.

Due-on-sale- A clause in a  mortgage contract requiring the borrower to pay the entire outstanding  balance upon sale or transfer of the property.

Dura board, dura rock- A panel made out of concrete and fiberglass usually used as a ceramic tile  backing material. Commonly used on bathtub decks. Sometimes called  Wonder board

DWV (drain-waste-vent)- The  section of a plumbing system that carries water and sewer gases out of a home.

Back To Top

Earnest Money- A sum paid to  the seller to show that a potential purchaser is serious about buying.

Earthquake Strap- A metal  strap used to secure gas hot water heaters to the framing or foundation  of a house. Intended to reduce the chances of having the water heater  fall over in an earthquake and causing a gas leak.

Easement- A formal contract  which allows a party to use another party's property for a specific  purpose. e.g. A sewer easement might allow one party to run a sewer line through a neighbors property.

Eaves- The horizontal exterior roof overhang.

Egress- A means of exiting the home. An egress window is required in every bedroom and basement.  Normally a 4' X 4' window is the minimum size required

Elbow (ell)- A plumbing or  electrical fitting that lets you change directions in runs of pipe or  conduit.

Electric lateral- The trench  or area in the yard where the electric service line (from a transformer  or pedestal) is located, or the work of installing the electric service  to a home.

Electric resistance coils-  Metal wires that heat up when electric current passes through them and  are used in baseboard heaters and electric water heaters.

Electrical entrance package-  The entry point of the electrical power including: (1) the 'strike' or  location where the overhead or underground electrical lines connect to  the house, (2) The meter which measures how much power is used and (3)  The 'panel' or 'circuit breaker box ' (or 'fuse box') where the power  can be shut off and where overload devices such a fuses or circuit  breakers and located.

Electrical Rough- Work  performed by the Electrical Contractor after the plumber and heating  contractor are complete with their phase of work. Normally all  electrical wires, and outlet, switch, and fixture boxes are installed  (before insulation).

Electrical Trim- Work  performed by the electrical contractor when the house is nearing  completion. The electrician installs all plugs, switches, light  fixtures, smoke detectors, appliance "pig tails", bath ventilation fans, wires the furnace, and "makes up" the electric house panel. The  electrician does all work necessary to get the home ready for and to  pass the municipal electrical final inspection

Elevation sheet- The page on  the blue prints that depicts the house or room as if a vertical plane  were passed through the structure.

Equity- The "valuation" that  you own in your home, i.e. the property value less the mortgage loan  outstanding.

Escrow - The handling of funds or documents by a third party on behalf of the buyer and/or seller.

Estimate- The amount of labor, materials, and other costs that a contractor anticipates for a project  as summarized in the contractor's bid proposal for the project.

Escutcheon- An ornamental  plate that fits around a pipe extending through a wall or floor to hide  the cut out hole

Estimating- The process of  calculating the cost of a project. This can be a formal and exact  process or a quick and imprecise process.

Evaporator coil- The part of a cooling system that absorbs heat from air in your home. Also see  condensing unit.

Expansion joint- Fibrous  material (@1/2" thick) installed in and around a concrete slab to permit it to move up and down (seasonally) along the non-moving foundation  wall.

Expansive soils- Earth that  swells and contracts depending on the amount of water that is present.  ("Betonite" is an expansive soil).

Exposed aggregate finish- A  method of finishing concrete which washes the cement/sand mixture off  the top layer of the aggregate - usually gravel. Often used in  driveways, patios and other exterior surfaces.

Extras- Additional work  requested of a contractor, not included in the original plan, which will be billed separately and will not alter the original contract amount,  but increase the cost of building the home.

Back To Top

FHA strap- Metal straps that  are used to repair a bearing wall "cut-out", and to "tie together" wall  corners, splices, and bearing headers. Also, they are used to hang  stairs and landings to bearing headers.

Face nail- To install nails  into the vertical face of a bearing header or beam.

Faced concrete- To finish the  front and all vertical sides of a concrete porch, step(s), or patio.  Normally the "face" is broom finished.

Facing brick- The brick used  and exposed on the outside of a wall. Usually these have a finished  texture.

Fascia- Horizontal boards  attached to rafter/truss ends at the eaves and along gables. Roof drain  gutters are attached to the fascia.

Felt- Tar paper. Installed  under the roof shingles. Normally 15 lb. or 30 lb.

Female- Any part, such as a  nut or fitting, into which another (male) part can be inserted. Internal threads are female.

Ferrule- Metal tubes used to  keep roof gutters "open". Long nails (ferrule spikes) are driven through these tubes and hold the gutters in place along the fascia of the home.

Field measure- To take  measurements (cabinets, countertops, stairs, shower doors, etc.) in the  home itself instead of using the blueprints.

Finger joint- A manufacturing  process of interlocking two shorter pieces of wood end to end to create a longer piece of dimensional lumber or molding. Often used in jambs and  casings and are normally painted (instead of stained).

Fire block- Short horizontal  members sometimes nailed between studs, usually about halfway up a wall. See also 'Fire stop'.

Fire brick- Brick made of  refractory ceramic material which will resist high temperatures. Used in a fireplace and boiler.

Fireplace chase flashing pan- A large sheet of metal that is installed around and perpendicular to the  fireplace flue pipe. It's purpose is to confine and limit the spread of  fire and smoke to a small area.

Fire-resistive or Fire rated-  Applies to materials that are not combustible in the temperatures of  ordinary fires and will withstand such fires for at least 1 hour.  Drywall used in the garage and party walls are to be fire rated, 5/8",  Type X.

Fire retardant chemical- A  chemical or preparation of chemicals used to reduce the flammability of a material or to retard the spread of flame.

Fire stop- A solid, tight  closure of a concealed space, placed to prevent the spread of fire and  smoke through such a space. In a frame wall, this will usually consist  of 2 by 4 cross blocking between studs. Work performed to slow the  spread of fire and smoke in the walls and ceiling (behind the drywall).  Includes stuffing wire holes in the top and bottom plates with  insulation, and installing blocks of wood between the wall studs at the  drop soffit line. This is integral to passing a Rough Frame inspection.   See also 'Fire block'.

Fishplate (gusset)- A wood or  plywood piece used to fasten the ends of two members together at a butt  joint with nails or bolts. Sometimes used at the junction of opposite  rafters near the ridge line. Sometimes called a gang nail plate.

Fish tape- A long strip of  spring steel used for fishing cables and for pulling wires through  conduit.

Fixed price contract- A  contract with a set price for the work. See Time and Materials Contract.

Fixed rate- A loan where the  initial payments are based on a certain interest rate for a stated  period .  The rate payable will not change during this period  regardless of changes in the lender's standard variable rate.

Fixed Rate Mortgage- A  mortgage with an interest rate that remains the same over the years.

Flagstone (flagging or flags)- Flat stones (1 to 4 inches thick) used for walks, steps, floors, and  vertical veneer (in lieu of brick).

Flakeboard- A manufactured  wood panel made out of 1"- 2" wood chips and glue. Often used as a  substitute for plywood in the exterior wall and roof sheathing. Also  called OSB or wafer board.

Flame retention burner- An oil burner, designed to hold the flame near the nozzle surface. Generally  the most efficient type for residential use.

Flashing- Sheet metal or other material used in roof and wall construction to protect a building from  water seepage.

Flat mold- Thin wood strips  installed over the butt seam of cabinet skins.

Flat paint- An interior paint  that contains a high proportion of pigment and dries to a flat or  lusterless finish.

Flatwork- Common word for  concrete floors, driveways, basements, and sidewalks.

Floating- The next-to-last  stage in concrete work, when you smooth off the job and bring water to  the surface by using a hand float or bull float.

Floating wall- A non-bearing  wall built on a concrete floor. It is constructed so that the bottom two horizontal plates can compress or pull apart if the concrete floor  moves up or down. Normally built on basements and garage slabs.

Fluorescent lighting- A  fluorescent lamp is a gas-filled glass tube with a phosphur coating on  the inside.  Gas inside the tube is ionized by electricity which causes the phosphur coating to glow.  Normally with two pins that extend from each end.

Flue- Large pipe through which fumes escape from a gas water heater, furnace, or fireplace. Normally  these flue pipes are double walled, galvanized sheet metal pipe and  sometimes referred to as a "B Vent". Fireplace flue pipes are normally  triple walled. In addition, nothing combustible shall be within one inch from the flue pipe.

Flue collar- Round metal ring  which fits around the heat flue pipe after the pipe passes out of the  roof.

Flue damper- An automatic door located in the flue that closes it off when the burner turns off;  purpose is to reduce heat loss up the flue from the still-warm furnace  or boiler.

Flue lining- 2-foot lengths,  fire clay or terra-cotta pipe (round or square) and usually madein all  ordinary flue sizes. Used for the inner lining of chimneys with the  brick or masonry work done around the outside. Flue linings in chimneys  runs from one foot below the flue connection to the top of the chimney.

Fly rafters- End rafters of  the gable overhang supported by roof sheathing and lookouts.

Footer, footing- Continuous 8" or 10" thick concrete pad installed before and supports the foundation  wall or monopost.

Forced air heating - A common  form of heating with natural gas, propane, oil or electricity as a fuel. Air is heated in the furnace and distributed through a set of metal  ducts to various areas of the house.

Form- Temporary structure  erected to contain concrete during placing and initial hardening.

Foundation- The supporting  portion of a structure below the first floor construction, or below  grade, including the footings.

Foundation ties- Metal wires  that hold the foundation wall panels and rebar in place during the  concrete pour.

Foundation waterproofing-  High-quality below-grade moisture protection. Used for below-grade  exterior concrete and masonry wall damp-proofing to seal out moisture  and prevent corrosion. Normally looks like black tar.

Frame Inspection- The act of  inspecting the home's structural integrity and it's complianceto local  municipal codes.

Framer-The carpenter  contractor that installs the lumber and erects the frame, flooring  system, interior walls, backing, trusses, rafters, decking, installs all beams, stairs, soffits and all work related to the wood structure of  the home. The framer builds the home according to the blueprints and  must comply with local building codes and regulations.

Framing- Lumber used for the  structural members of a building, such as studs, joists, and rafters.

Frieze- In house construction a horizontal member connecting the top of the siding with the soffit of  the cornice.

Frost lid- Round metal lid  that is installed on a water meter pit.

Frost line- The depth of frost penetration in soil and/or the depth at which the earth will freeze and swell. This depth varies in different parts of the country.

Furring strips- Strips of  wood, often 1 X 2 and used to shim out and provide a level fastening  surface for a wall or ceiling.

Fuse- A device often found in  older homes designed to prevent overloads in electrical lines. This  protects against fire. See also 'circuit breakers'.

Back To Top

GF C I, or G F I- Ground Fault Circuit Interrupter- an ultra sensitive plug designed to shut off all  electric current. Used in bathrooms, kitchens, exterior waterproof  outlets, garage outlets, and "wet areas". Has a small reset button on  the plug.

Gable- The end, upper,  triangular area of a home, beneath the roof.

Gang nail plate- A steel plate attached to both sides at each joint of a truss. Sometimes called a  fishplate or gussett.

Gate valve- A valve that lets  you completely stopâ€â€�but not modulateâ€â€�the flow within a pipe.

General Contractor A  contractor who enters into a contract with the owner of a project for  the construction of the project and who takes full responsibility for  its completion, although the contractor may enter into subcontracts with others for the performance of specific parts or phases of the project.

Gas lateral- The trench or  area in the yard where the gas line service is located, or the work of  installing the gas service to a home.

Girder- A large or principal  beam of wood or steel used to support concentrated loads at isolated  points along its length.

Glazing- The process of  installing glass, which commonly is secured with glazier's points and  glazing compound.

Globe valve- A valve that lets you adjust the flow of water to any rate between fully on and fully  off. Also see gate valve.

Gloss enamel- A finishing  paint material. Forms a hard coating with maximum smoothness of surface  and dries to a sheen or luster (gloss)

Glued Laminated Beam (Glulam)- A structural beam composed of wood laminations or lams. The lams are  pressure bonded with adhesives to attain a typical thickness of 1 ½" .  (It looks like 5 or more 2 X 4's are glued together).

Grade- Ground level, or the  elevation at any given point. Also the work of leveling dirt. Also the  designated quality of a manufactured piece of wood.

Grade beam- A foundation wall  that is poured @ level with or just below the grade of theearth. An  example is the area where the 8' or 16' overhead garage door "block out" is located, or a lower (walk out basement) foundation wall is poured

Graduated Payment Mortgage (GPM) - A fixed-rate, fixed-schedule loan. It starts with lower payments than a level payment loan; payments rise annually, with the entire increase  being used to reduce the outstanding balance. The increase in payments  may enable the borrower to pay off a 30-year loan in 15 to 20 years, or  less.

Grain- The direction, size,  arrangement, appearance, or quality of the fibers in wood.

Grid- The completed assembly  of main and cross tees in a suspended ceiling system before the ceiling  panels are installed. Also the decorative slats (munton) installed  between glass panels.

Ground- Refers to  electricity's habit of seeking the shortest route to earth. Neutral  wires carry it there in all circuits. An additional grounding wire or  the sheathing of the metal-clad cable or conduitâ€â€�protects against  shock if the neutral leg is interrupted.

Ground fault- Ground Fault  Circuit Interrupter (GFCI, GFI)- an ultra sensitive plug designed to  shut off all electric current. Used in bathrooms, kitchens, exterior  waterproof outlets, garage outlets, and "wet areas". Has a small reset  button on the plug.

Ground iron- The plumbing  drain and waste lines that are installed beneath the basement floor.  Cast iron was once used, but black plastic pipe (ABS) is now widely  used.

Groundwater- Water from an  aquifer or subsurface water source.

Grout- A wet mixture of  cement, sand and water that flows into masonry or ceramic crevices to  seal the cracks between the different pieces. Mortar made of such  consistency (by adding water) that it will flow into the joints and  cavities of the masonry work and fill them solid.

Gusset- A flat wood, plywood,  or similar type member used to provide a connection at the intersection  of wood members. Most commonly used at joints of wood trusses. They are  fastened by nails, screws, bolts, or adhesives.

Gutter- A shallow channel or  conduit of metal or wood set below and along the (fascia) eaves of a  house to catch and carry off rainwater from the roof.

Gyp board- Drywall. Wall board or gypsum- A panel (normally 4' X 8', 10', 12', or 16')made with a core of Gypsum (chalk-like) rock, which covers interior walls and ceilings.

Gypsum plaster- Gypsum  formulated to be used with the addition of sand and water for base-coat  plaster.

Back To Top

H Clip- Small metal clips  formed like an "H" that fits at the joints of two plywood (or wafer  board) sheets to stiffen the joint. Normally used on the roof sheeting.

Hardware- All of the "metal"  fittings that go into the home when it is near completion. For example,  door knobs, towel bars, handrail brackets, closet rods, house numbers,  door closers, etc. The Interior Trim Carpenter installs the "hardware".

Haunch- An extension, knee  like protrusion of the foundation wall that a concrete porch or patio  will rest upon for support.

Hazard insurance - Protection  against damage caused by fire, windstorms, or other common hazards. Many lenders require borrowers to carry it in an amount at least equal to  the mortgage.

Header- (a) A beam placed  perpendicular to joists and to which joists are nailed inframing for a  chimney, stairway, or other opening. (b) A wood lintel. (c) The  horizontal structural member over an opening (for example over a door or window).

Hearth- The fireproof area  directly in front of a fireplace. The inner or outer floor of a  fireplace, usually made of brick, tile, or stone.

Heating load- The amount of  heating required to keep a building at a specified temperature during  the winter, usually 65° F, regardless of outside temperature.

Heat meter- An electrical  municipal inspection of the electric meter breaker panel box.

Heat pump- A mechanical device which uses compression and decompression of gas to heat and/or cool a  house.

Heat Rough- Work performed by  the Heating Contractor after the stairs and interior walls are built.  This includes installing all duct work and flue pipes. Sometimes, the  furnace and fireplaces are installed at this stage of construction.

Heat Trim- Work done by the  Heating Contractor to get the home ready for the municipal Final Heat  Inspection. This includes venting the hot water heater, installing all  vent grills, registers, air conditioning services, turning on the  furnace, installing thermostats, venting ranges and hoods, and all other heat related work.

Heel cut- A notch cut in the  end of a rafter to permit it to fit flat on a wall and on the top,  doubled, exterior wall plate.

Highlights- A light spot,  area, or streak on a painted surface.

Hip- A roof with four sloping  sides. The external angle formed by the meeting of two sloping sides of a roof.

Hip roof- A roof that rises by inclined planes from all four sides of a building.

Home run (electrical)- The  electrical cable that carries power from the main circuit breaker panel  to the first electrical box, plug, or switch in the circuit.

Honey combs- The appearance  concrete makes when rocks in the concrete are visible and where there  are void areas in the foundation wall, especially around concrete  foundation windows.

Hose bib- An exterior water  faucet (sill cock).

Hot wire- The wire that  carries electrical energy to a receptacle or other device €�in contrast  to a neutral, which carries electricity away again. Normally the black  wire. Also see ground.

Humidifier- An appliance  normally attached to the furnace, or portable unit device designed to  increase the humidity within a room or a house by means of the discharge of water vapor.

Hurricane clip- Metal straps  that are nailed and secure the roof rafters and trusses to the top  horizontal wall plate. Sometimes called a Teco clip.

H V A C- An abbreviation for Heat,Ventilation, andAir Conditioning

Back To Top

I-beam- A steel beam with a  cross section resembling the letterI. It is used for long spans  as basement beams or over wide wall openings, such as a double garage  door, when wall and roof loads bear down on the opening.

I-joist- Manufactured  structural building component resembling the letter "I". Used as floor  joists and rafters. I-joists include two key parts:flanges and webs. The flange of the I joist may be made of laminated veneer lumber or dimensional lumber, usually formed into a 1½" width. The web or center of the I-joist is commonly made of plywood or oriented strand board (OSB). Large holes can be cut in the web to accommodate duct work and plumbing waste lines. I-joists are available in lengths up to 60  feet long

Incandescent lamp- A lamp  employing an electrically charged metal filament that glows at white  heat. A typical light bulb.

Index- The interest rate or  adjustment standard that determines the changes in monthly payments for  an adjustable rate loan.

Infiltration- The passage of  air from indoors to outdoors and vice versa; term is usually associated  with drafts from cracks, seams or holes in buildings.

Inside corner- The point at  which two walls form an internal angle, as in the corner of a room.

Insulating glass- Window or  door in which two panes of glass are used with a sealed air space  between.  Also known as Double glass.

Insulation board, rigid- A  structural building board made of coarse wood or cane fiber in ½- and  25/32-inch thickness. It can be obtained in various size sheets and  densities.

Insulation- Any material high  in resistance to heat transmission that, when placed in the walls,  ceiling, or floors of a structure, and will reduce the rate of heat  flow.

Interest - The cost paid to a  lender for borrowed money.

Interior finish- Material used to cover the interior framed areas of walls and ceilings

Irrigation- Lawn sprinkler  system.

Back To Top

J Channel- Metal edging used  on drywall to give the edge a better finished appearance when a wall is  not "wrapped" Generally, basement stairway walls have drywall only on  the stair side. J Channel is used on the vertical edge of the last  drywall sheet

Jack post- A type of  structural support made of metal, which can be raised or lowered through a series of pins and a screw to meet the height required. Basically  used as a replacement for an old supporting member in a building. See  Monopost.

Jack rafter- A rafter that  spans the distance from the wall plate to a hip, or from a valley to a  ridge.

Jamb- The side and head lining of a doorway, window, or other opening. Includes studs as well as the  frame and trim.

Joint- The location between  the touching surfaces of two members or components joined and held  together by nails, glue, cement, mortar, or other means.

Joint cement or Joint compound- A powder that is usually mixed with water and used for joint treatment  in gypsum-wallboard finish. Often called "spackle" or drywall mud.

Joint tenancy- A form of  ownership in which the tenants own a property equally. If one dies, the  other automatically inherits the entire property.

Joint trench- When the  electric company and telephone company dig one trench and "drop" both of their service lines in.

Joist- Wooden 2 X 8's, 10's,  or 12's that run parallel to one another and support a floor or ceiling, and supported in turn by larger beams, girders, or bearing walls.

Joist hanger- A metal "U"  shaped item used to support the end of a floor joist and attached with  hardened nails to another bearing joist or beam.

Jumpers- Water pipe installed  in a water meter pit (before the water meter is installed), or electric  wire that is installed in the electric house panel meter socket before  the meter is installed. This is sometimes illegal.

Back To Top

Keeper- The metal latch plate  in a door frame into which a doorknob plunger latches.

Keyless- A plastic or  porcelain light fixture that operates by a pull string. Generally found  in the basement, crawl space , and attic areas.

Keyway- A slot formed and  poured on a footer or in a foundation wall when another wall will be  installed at the slot location. This gives additional strength to the  joint/meeting point.

Kilowatt (kw)- One thousand  watts. A kilowatt hour is the base unit used in measuring electrical  consumption. Also see watt.

King stud- The vertical "2  X's" frame lumber (left and right) of a window or door opening, and runs continuously from the bottom sole plate to the top plate.

Knot- In lumber, the portion  of a branch or limb of a tree that appears on the edge or face of the  piece.

Back To Top

Laminated shingles - Shingles  that have added dimensionality because of extra layers or tabs, giving a shake-like appearance. May also be called "architectural shingles" or  "three-dimensional shingles."

Laminating- Bonding together  two or more layers of materials.

Landing- A platform between  flights of stairs or at the termination of a flight of stairs. Often  used when stairs change direction. Normally no less than 3 ft. X 3 ft.  square.

Lap- To cover the surface of  one shingle or roll with another.

Latch- A beveled metal tongue  operated by a spring-loaded knob or lever. The tongue's bevel lets you  close the door and engage the locking mechanism, if any, without using a key. Contrasts with dead bolt.

Lateral (electric, gas, telephone, sewer and water)- The underground trench and related services  (i.e., electric, gas, telephone, sewer and water lines) that will be  buried within the trench.

Lath- A building material of  narrow wood, metal, gypsum, or insulating board that is fastened to the  frame of a building to act as a base for plaster, shingles, or tiles.

Lattice- An open framework of  criss-crossed wood or metal strips that form regular, patterned spaces.

Ledger (for a Structural Floor)- The wooden perimeter frame lumber member that bolts onto the face of a  foundation wall and supports the wood structural floor.

Ledger strip- A strip of  lumber nailed along the bottom of the side of a girder on which joists  rest.

Leech field- A method used to  treat/dispose of sewage in rural areas not accessible to a municipal  sewer system.  Sewage is permitted to be filtered and eventually  discharged into a section of the lot called a leech field.

Let-in brace- Nominal 1  inch-thick boards applied into notched studs diagonally. Also, an "L"  shaped, long (@ 10') metal strap that are installed by the framer at the rough stage to give support to an exterior wall or wall corner.

Level- True horizontal. Also a tool used to determine level.

Level Payment Mortgage- A  mortgage with identical monthly payments over the life of the loan.

Lien- An encumbrance that  usually makes real or personal property the security for payment of a  debt or discharge of an obligation.

Light- Space in a window sash  for a single pane of glass. Also, a pane of glass.

Limit switch- A safety control that automatically shuts off a furnace if it gets too hot. Most also  control blower cycles.

Lineal foot- A unit of measure for lumber equal to 1 inch thick by 12 inches wide by 12 inches long.  Examples: 1" x 12" x 16' = 16 board feet, 2" x 12" x 16' = 32 board  feet.

Lintel- A horizontal  structural member that supports the load over an opening such as a door  or window.

Load bearing wall- Includes  all exterior walls and any interior wall that is aligned above a support beam or girder. Normally, any wall that has a double horizontal top  plate.

Loan- The amount to be  borrowed.

Loan to value ratio- The ratio of the loan amount to the property valuation and expressed as a  percentage. E.g. if a borrower is seeking a loan of $200,000 on a  property worth $400,000 it has a 50% loan to value rate. If the loan  were $300,000, the LTV would be 75%. The higher the loan to value, the  greater the lender's perceived risk. Loans above normal lending LTV  ratios may require additional security.

Lookout- A short wood bracket  or cantilever that supports an overhang portion of a roof.

Louver- A vented opening into  the home that has a series of horizontal slats and arranged to permit  ventilation but to exclude rain, snow, light, insects, or other living  creatures.

Lumens- Unit of measure for  total light output. The amount of light falling on a surface of one  square foot.

Back To Top

Male- Any part, such as a  bolt, designed to fit into another (female) part. External threads are  male.

Mantel- The shelf above a  fireplace opening. Also used in referring to the decorative trim around a fireplace opening.

Manufactured wood- A wood  product such as a truss, beam, gluelam, microlam or joist which is  manufactured out of smaller wood pieces and glued or mechanically  fastened to form a larger piece. Often used to create a stronger member  which may use less wood. See also Oriented Strand Board.

Manufacturer's specifications- The written installation and/or maintenance instructions which are  developed by the manufacturer of a product and which may have to be  followed in order to maintain the product warrantee.

Masonry- Stone, brick,  concrete, hollow-tile, concrete block, or other similar building units  or materials. Normally bonded together with mortar to form a wall.

Mastic- A pasty material used  as a cement (as for setting tile) or a protective coating (as for  thermal insulation or waterproofing)

Mechanics lien- A lien on real property, created by statue in many years, in favor of persons  supplying labor or materials for a building or structure, for the value  of labor or materials supplied by them. In some jurisdictions, a  mechanics lien also exists for the value of professional services. Clear title to the property cannot be obtained until the claim for the labor, materials, or professional services is settled. Timely filing is  essential to support the encumbrance, and prescribed filing dates vary  by jurisdiction.

Metal lath- Sheets of metal  that are slit to form openings within the lath. Used as a plaster base  for walls and ceilings and as reinforcing over other forms of plaster  base.

Microlam- A manufactured  structural wood beam. It is constructed of pressure and adhesive bonded  wood strands of wood. They have a higher strength rating than solid sawn lumber. Normally comes in l½" thickness' and 9½", 11½" and 14"  widths

Milar (mylar)- Plastic,  transparent copies of a blueprint.

Millwork- Generally all  building materials made of finished wood and manufactured in millwork  plants. Includes all doors, window and door frames, blinds, mantels,  panelwork, stairway components (ballusters, rail, etc.), moldings, and  interior trim. Does not include flooring, ceiling, or siding.

Miter joint- The joint of two  pieces at an angle that bisects the joining angle. For example, the  miter joint at the side and head casing at a door opening is made at a  45° angle.

Molding- A wood strip having  an engraved, decorative surface.

Monopost- Adjustable metal  column used to support a beam or bearing point. Normally 11 gauge or  Schedule 40 metal, and determined by the structural engineer

Mortar- A mixture of cement  (or lime) with sand and water used in masonry work.

Mortgage- Loan secured by  land.

Mortgage broker - A broker who represents numerous lenders and helps consumers find affordable  mortgages; the broker charges a fee only if the consumer finds a loan.

Mortgage company - A company  that borrows money from a bank, lends it to consumers to buy homes, then sells the loans to investors.

Mortgage deed- Legal document  establishing a loan on property.

Mortgagee- The lender who  makes the mortgage loan.

Mortgage loan- A contract in  which the borrower's property is pledged as collateral. It is repaid in  installments. The mortgagor (buyer) promises to repay principal and  interest, keep the home insured, pay all taxes and keep the property in  good condition.

Mortgage Origination Fee- A  charge for work involved in preparing and servicing a mortgage  application (usually one percent of the loan amount).

Mortise- A slot cut into a  board, plank, or timber, usually edgewise, to receive the tenon (or  tongue) of another board, plank, or timber to form a joint.

Mudsill- Bottom horizontal  member of an exterior wall frame which rests on top a foundation,  sometimes called sill plate. Also sole plate, bottom member of interior  wall frame.

Mullion- A vertical divider in the frame between windows, doors, or other openings.

Muntin- A small member which  divides the glass or openings of sash or doors.

Muriatic acid- Commonly used  as a brick cleaner after masonry work is completed.

Mushroom- The unacceptable  occurrence when the top of a caisson concrete pier spreads out and  hardens to become wider than the foundation wall thickness.

Back To Top

Nail inspection- An inspection made by a municipal building inspector after the drywall material is  hung with nails and screws (and before taping).

Natural finish- A transparent  finish which does not seriously alter the original color or grain of the natural wood. Natural finishes are usually provided by sealers, oils,  varnishes, water repellent preservatives, and other similar materials.

NEC (National Electrical Code)- A set of rules governing safe wiring methods. Local codesâ€â€�which are  backed by lawâ€â€�may differ from the NEC in some ways.

Neutral wire- Usually  color-coded white, this carries electricity from an outlet back to the  service panel. Also see hot wire and ground.

Newel post- The large starting post to which the end of a stair guard railing or balustrade is  fastened.

Nonbearing wall- A wall  supporting no load other than its own weight.

Nosing- The projecting edge of a molding or drip or the front edge of a stair tread.

Notch- A crosswise groove at  the end of a board.

Note- A formal document  showing the existence of a debt and stating the terms of repayment.

Nozzle- The part of a heating  system that sprays the fuel of fuel-air mixture into the combustion  chamber.

Back To Top

O C- On Center- The  measurement of spacing for studs, rafters, and joists in a building from the center of one member to the center of the next.

Oakum- Loose hemp or jute  fiber that's impregnated with tar or pitch and used to caulk large seams or for packing plumbing pipe joints

Open hole inspection- When an  engineer (or municipal inspector) inspects the open excavation and  examines the earth to determine the type of foundation (caisson, footer, wall on ground, etc.) that should be installed in the hole.

Oriented Strand Board or OSB- A manufactured 4' X 8' wood panel made out of 1"- 2" wood chips and glue. Often used as a substitute for plywood.

Outrigger- An extension of a  rafter beyond the wall line. Usually a smaller member nailed to a larger rafter to form a cornice or roof overhang.

Outside corner- The point at  which two walls form an external angle, one you usually can walk around.

Overhang- Outward projecting  eave-soffit area of a roof; the part of the roof that hangs out or over  the outside wall. See also Cornice.

Back To Top

Padding- A material installed  under carpet to add foot comfort, isolate sound, and to prolong carpet  life.

Pad out, pack out- To shim out or add strips of wood to a wall or ceiling in order that the finished  ceiling/wall will appear correct.

Paint- A combination of  pigments with suitable thinners or oils to provide decorative and  protective coatings. Can be oil based or latex water based.

Pallets- Wooden platforms used for storing and shipping material. Forklifts and hand trucks are used  to move these wooden platforms around.

Panel- A thin flat piece of  wood, plywood, or similar material, framed by stiles and rails as in a  door (or cabinet door), or fitted into grooves of thicker material with  molded edges for decorative wall treatment.

Paper, building- A general  term for papers, felts, and similar sheet materials used in buildings  without reference to their properties or uses. Generally comes in long  rolls.

Parapet- A wall placed at the  edge of a roof to prevent people from falling off.

Parting stop or strip- A small wood piece used in the side and head jambs of double hung windows to  separate the upper sash from the lower sash.

Particle board- Plywood  substitute made of course sawdust that is mixed with resin and pressed  into sheets. Used for closet shelving, floor underlayment, stair treads, etc.

Partition- A wall that  subdivides spaces within any story of a building or room.

Paver, paving-  Materials commonly masonry €�laid down to make a firm, even surface.

Payment schedule- A pre-agreed upon schedule of payments to a contractor usually based upon the amount of work completed. Such a schedule may include a deposit prior to the  start of work. There may also be a temporary 'retainer' (5-10% of the  total cost of the job) at the end of the contract for correcting any  small items which have not been completed or repaired.

Pedestal- A metal box  installed at various locations along utility easements that contain  electrical, telephone, or cable television switches and connections.

Penalty clause - A provision  in a contract that provides for a reduction in the amount otherwise  payable under a contract to a contractor as a penalty for failure to  meet deadlines or for failure of the project to meet contract  specifications.

Penny- As applied to nails, it originally indicated the price per hundred. The term now series as a  measure of nail length and is abbreviated by the letter "d".  Normally, 16d (16 "penny") nails are used for framing

Percolation test or perc. test- Tests that a soil engineer performs on earth to determine the  feasibility of installing a leech field type sewer system on a lot. A  test to determine if the soil on a proposed building lot is capable of  absorbing the liquid affluent from a septic system.

Performance bond- An amount of money (usually 10% of the total price of a job)  that a contractor  must put on deposit with a governmental agency as an insurance policy  that guarantees the contractors' proper and timely completion of a  project or job.

Perimeter drain- 3" or 4"  perforated plastic pipe that goes around the perimeter (either inside or outside) of a foundation wall (before backfill) and collects and  diverts ground water away from the foundation. Generally, it is  "daylighted" into a sump pit inside the home, and a sump pump is  sometimes inserted into the pit to discharge any accumulation of water.

Permeability- A measure of the ease with which water penetrates a material.

Permit - A governmental  municipal authorization to perform a building process as in:

• Zoning\Use permit - Authorization to use a property for a specific use e.g. a garage, a single family  residence etc.
• Demolition permit - Authorization to tear down and remove an existing structure.
• Grading permit - Authorization to change the contour of the land.
• Septic permit - A health  department authorization to build or modify a septic system.
• Building permit - Authorization  to build or modify a structure.
• Electrical permit - A separate  permit required for most electrical work.
• Plumbing permit - A separate  permit required for new plumbing and larger modifications of existing  plumbing systems.

Pigtails, electrical- The  electric cord that the electrician provides and installs on an appliance such as a garbage disposal, dishwasher, or range hood.

Pier- A column of masonry,  usually rectangular in horizontal cross section, used to support other  structural members. Also see Caisson.

Pigment- A powdered solid used in paint or enamel to give it a color.

Pilot hole- A small-diameter,  pre-drilled hole that guides a nail or screw.

Pilot light- A small,  continuous flame (in a hot water heater, boiler, or furnace) that  ignites gas or oil burners when needed.

Pitch- The incline slope of a  roof or the ratio of the total rise to the total width of a house, i.e., a 6-foot rise and 24-foot width is a one-fourth pitch roof. Roof slope  is expressed in the inches of rise, per foot of horizontal run.

PITI - Principal, interest,  taxes and insurance (the four major components of monthly housing  payments).

Plan view- Drawing of a  structure with the view from overhead, looking down.

Plate- Normally a 2 X 4 or 2 X 6 that lays horizontally within a framed structure, such as:

• Sill plate- A horizontal member anchored to a concrete or  masonry wall.
• Sole plate- Bottom horizontal member of a frame wall.
• Top plate- Top horizontal member of a frame wall supporting  ceiling joists, rafters, or other members.

Plenum- The main hot-air supply duct leading from a furnace.

Plot plan- An overhead view plan that shows the location of the home on the lot.  Includes all easements, property lines, set backs, and legal  descriptions of the home. Provided by the surveyor.

Plough,  plow- To cut a lengthwise groove in a board or plank. An exterior  handrail normally has a ploughed groove for hand gripping purposes

Plumb-  Exactly vertical and perpendicular.

Plumb bob- A lead weight attached to a string. It is the tool used in determining  plumb.

Plumbing  boots- Metal saddles used to strengthen a bearing wall/vertical  stud(s) where a plumbing drain line has been cut through and installed.

Plumbing  ground- The plumbing drain and waste lines that are installed  beneath a basement floor.

Plumbing  jacks- Sleeves that fit around drain and waste vent pipes at, and  are nailed to, the roof sheeting.

Plumbing  rough- Work performed by the plumbing contractor after the Rough  Heat is installed. This work includes installing all plastic ABS drain  and waste lines, copper water lines, bath tubs, shower pans, and gas  piping to furnaces and fireplaces. Lead solder should not be used on  copper piping.

Plumbing  stack- A plumbing vent pipe that penetrates the roof.

Plumbing  trim- Work performed by the plumbing contractor to get the home  ready for a final plumbing inspection. Includes installing all toilets  (water closets), hot water heaters, sinks, connecting all gas pipe to  appliances, disposal, dishwasher, and all plumbing items.

Plumbing  waste line- Plastic pipe used to collect and drain sewage waste.

Ply- A  term to denote the number of layers of roofing felt, veneer in plywood,  or layers in built-up materials, in any finished piece of such material.

Plywood- A panel (normally 4' X 8') of wood made of three or more layers of  veneer, compressed and joined with glue, and usually laid with the grain of adjoining plies at right angles to give the sheet strength.

Point load- A point where a bearing/structural weight is concentrated and  transferred to the foundation.

Portland  cement- Cement made by heating clay and crushed limestone into a  brick and then grinding to a pulverized powder state.

Post- A vertical framing member usually designed to carry a beam. Often a 4" x  4", a 6" x 6", or a metal pipe with a flat plate on top and bottom.

Post-and-beam- A basic building method that uses just a few hefty posts and beams to  support an entire structure. Contrasts with stud framing.

Power vent- A vent that includes a fan to speed up air flow.  Often installed on  roofs.

Premium- Amount payable on a loan.

Preservative-. Any pesticide substance that, for a reasonable length of time, will  prevent the action of wood-destroying fungi, insect borers, and similar  destructive agents when the wood has been properly coated or impregnated with it. Normally an arsenic derivative. Chromated Copper Arsenate  (CCA) is an example.

Pressure  Relief Valve (PRV)- A device mounted on a hot water heater or boiler which is designed to release any high steam pressure in the tank to  prevent tank explosions.

Pressure-treated wood- Lumber that has been saturated with a preservative.

Primer- The first, base coat of paint when a paint job consists of two or more  coats. A first coating formulated to seal raw surfaces and holding  succeeding finish coats.

Principal- The original amount of the loan, the capital.

Property  survey- A survey to determine the boundaries of your property. The  cost depends on the complexity of the survey.

P trap- Curved, "U" section of drain pipe that holds a water seal to  prevent sewer gasses from entering the home through a fixtures water  drain.

Pump mix- Special concrete that will be used in a concrete pump. Generally, the  mix has smaller rock aggregate than regular mix.

Punch list- A list of discrepancies that need to be corrected by the contractor.

Punch out- To inspect and make a discrepancy list.

Putty- A type of dough used in sealing glass in the sash, filling small holes  and crevices in wood, and for similar purposes.

PVC or CPVC - Poly Vinyl Chloride-A type of white or light gray plastic pipe  sometimes used for water supply lines and waste pipe.

Back To Top

Quarry tile- A man-made or machine-made clay tile used to finish a floor or wall.  Generally 6" X  6" X 1/4" thick .

Quarter  round- A small trim molding that has the cross section of a quarter  circle.

Back To Top

Rabbet- A rectangular longitudinal groove cut in the corner edge of a board or  plank.

Radiant  heating- A method of heating, usually consisting of a forced hot  water system with pipes placed in the floor, wall, or ceiling. Also  electrically heated panels.

Radiation- Energy transmitted from a heat source to the air around it. Radiators  actually depend more on convection than radiation.

Radon- A naturally-occurring, heavier than air, radioactive gas common in many  parts of the country. Radon gas exposure is associated with lung  cancer. Mitigation measures may involve crawl space and basement venting and various forms of vapor barriers.

Radon  system- A ventilation system beneath the floor of a basement and/or  structural wood floor and designed to fan exhaust radon gas to the  outside of the home

Rafter- Lumber used to support the roof sheeting and roof loads. Generally, 2 X 10's and 2 X 12's are used. The rafters of a flat roof are sometimes  called roof joists.

Rafter, hip- A rafter that forms the intersection of an external roof angle.

Rafter,  valley- A rafter that forms the intersection of an internal roof  angle. The valley rafter is normally made of double 2-inch-thick  members.

Rail-  Cross members of panel doors or of a sash. Also, a wall or open  balustrade placed at the edge of a staircase, walkway bridge, or  elevated surface to prevent people from falling off. Any relatively  lightweight horizontal element, especially those found in fences (split  rail).

Railroad  tie- Black, tar and preservative impregnated, 6" X 8" and 6'-8' long wooden timber that was used to hold railroad track in place. Normally  used as a member of a retaining wall.

Rake-  Slope or slanted.

Rake fascia- The vertical face of the sloping end of a roof eave.

Rake siding- The practice of installing lap siding diagonally

Ranch- A single story, one level home.

Ready mixed concrete- Concrete mixed at a plant or in trucks en route to a job  and delivered ready for placement.

Rebar,  reinforcing bar-Ribbed steel bars installed in foundation concrete  walls, footers, and poured in place concrete structures designed to  strengthen concrete. Comes in various thickness' and strength grade.

Receptacle- An electrical outlet. Typical household will have many 120 volt  receptacles for plugging in lams and appliances and 240 volt receptacles for the range, clothes dryer, air conditioners, etc.

Recording  fee - A charge for recording the transfer of a property, paid to a  city, county, or other appropriate branch of government.

Redline,  red lined prints- Blueprints that reflect changes and that are  marked with red pencil.

Reducer- A fitting with different size openings at either end and used to go  from a larger to a smaller pipe.

Reflective  insulation- Sheet material with one or both faces covered with  aluminum foil.

Refrigerant- A substance that remains a gas at low temperatures and pressure and can be used to transfer heat. Freon is an example and is used in air  conditioning systems.

Register- A grill placed over a heating duct or cold air return.

Reglaze- To replace a broken window.

Relief  valve- A device designed to open if it detects excess temperature or pressure.

Remote- Remote electrical, gas, or water meter digital readouts that are  installed near the front of the home in order for utility companies to  easily read the home owners usage of the service.

Retaining  wall- A structure that holds back a slope and prevents erosion.

Retentions- Amounts withheld from progress billings until final and satisfactory  project completion.

R factor or value- A measure of a materials resistance to the passage of heat.  New homewalls are usually insulated with 4" of batt insulation with an R value of R-13, and a ceiling insulation of R-30.

Ribbon  (girt)- Normally a 1 X 4 board let into the studs horizontally to  support the ceiling or second-floor joists.

Ridge-  The horizontal line at the junction of the top edges of two sloping roof surfaces.

Ridge board- The board placed on the ridge of the roof onto which the upper ends of  other rafters are fastened.

Ridge  shingles- Shingles used to cover the ridge board.

Rim joist- A joist that runs around the perimeter of the floor joists and home.

Rise-  The vertical distance from the eaves line to the ridge. Also the  vertical distance from stair tread to stair tread (and not to exceed 7  ½").

Riser-  Each of the vertical boards closing the spaces between the treads of  stairways.

Riser and  panel- The exterior vertical pipe (riser) and metal electric box  (panel) the electrician provides and installs at the "Rough Electric"  stage.

Road base- A aggregate mixture of sand and stone.

Rock 1, 2, 3- When referring to drywall, this means to install drywall to the walls  and ceilings (with nails and screws), and before taping is performed.

Roll,  rolling- To install the floor joists or trusses in their correct  place. (To "roll the floor" means to install the floor joists).

Romex- A name brand of nonmetallic sheathed electrical cable that is used for  indoor wiring.

Roll  roofing- Asphalt roofing products manufactured in roll form. 36-inch wide rolls with and 108 square feet of material. Weights are generally  45 to 90 pounds per roll.

Romex- A name brand of nonmetallic sheathed electrical cable that is used for  indoor wiring.

Roof jack- Sleeves that fit around the black plumbing waste vent pipes at, and are nailed to, the roof sheeting.

Roof joist- The rafters of a flat roof. Lumber used to support the roof sheeting  and roof loads. Generally, 2 X 10's and 2 X 12's are used.

Roof  sheathing or sheeting- The wood panels or sheet material fastened to the roof rafters or trusses on which the shingle or other roof covering is laid.

Roof valley- The "V" created where two sloping roofs meet.

Rough  opening- The horizontal and vertical measurement of a window or door opening before drywall or siding is installed.

Rough sill- The framing member at the bottom of a rough opening for a window. It is attached to the cripple studs below the rough opening.

Roughing-in- The initial stage of a plumbing, electrical, heating, carpentry, and/or other project, when all components that won't be seen after the second  finishing phase are assembled. See also Heat Rough, Plumbing Rough, and  Electrical Rough.

Run, roof - The horizontal distance from the eaves to a point directly under the  ridge. One half the span.

Run, stair- the horizontal distance of a stair tread from the nose to the riser.

R Value- A measure of insulation. A measure of a materials resistance to the  passage of heat. The higher the R value, the more insulating "power" it  has. For example, typical new home's walls are usually insulated with 4" of batt insulation with an R value of R-13, and a ceiling insulation of R-30.

Back To Top

Saddle- A small second roof built behind the back side of a fireplace chimney  to divert water around the chimney. Also, the plate at the bottom of  some €�usually exterior door openings. Sometimes called a threshold.

Sack mix- The amount of Portland cement in a cubic yard of concrete mix.  Generally, 5 or 6 sack is required in a foundation wall.

Sales  contract - A contract between a buyer and seller which should  explain: (1) What the purchase includes, (2) What guarantees there are,  (3) When the buyer can move in, (4) What the closing costs are, and (5)  What recourse the parties have if the contract is not fulfilled or if  the buyer cannot get a mortgage commitment at the agreed upon time.

Sand float  finish- Lime that is mixed with sand, resulting in a textured finish on a wall.

Sanitary  sewer- A sewer system designed for the collection of waste water  from the bathroom, kitchen and laundry drains, and is usually not  designed to handle storm water.

Sash- A single light frame containing one or more lights of glass. The frame  that holds the glass in a window, often the movable part of the window.

Sash  balance- A device, usually operated by a spring and designed to hold a single hung window vent up and in place

Saturated  felt- A felt which is impregnated with tar or asphalt.

Schedule  (window, door, mirror)- A table on the blueprints that list the  sizes, quantities and locations of the windows, doors and mirrors.

Scrap out- The removal of all drywall material and debris after the home is "hung  out" (installed) with drywall.

Scratch  coat- The first coat of plaster, which is scratched to form a bond  for a second coat.

Screed,  concrete- To level off concrete to the correct elevation during a  concrete pour.

Screed,  plaster- A small strip of wood, usually the thickness of the plaster coat, used as a guide for plastering.

Scribing- Cutting and fitting woodwork to an irregular surface.

Scupper- (1) An opening for drainage in a wall, curb or parapet. (2) The drain  in a downspout or flat roof, usually connected to the downspout.

Sealer- A finishing material, either clear or pigmented, that is usually  applied directly over raw wood for the purpose of sealing the wood  surface.

Seasoning- Drying and removing moisture from green wood in order to improve its  usability.

Self-sealing shingles- Shingles containing factory-applied strips or spots of  self-sealing adhesive.

Semigloss  paint or enamel- A paint or enamel made so that its coating, when  dry, has some luster but is not very glossy. Bathrooms and kitchens are  normally painted semi-gloss

Septic  system- An on site waste water treatment system. It usually has a  septic tank which promotes the biological digestion of the waste, and a  drain field which is designed to let the left over liquid soak into the  ground. Septic systems and permits are usually sized by the number of  bedrooms in a house.

Service  entrance panel- Main power cabinet where electricity enters a home  wiring system.

Service  equipment- Main control gear at the service entrance, such as  circuit breakers, switches, and fuses.

Service  lateral- Underground power supply line.

Setback  Thermostat- A thermostat with a clock which can be programmed to  come on or go off at various temperatures and at different times of the  day/week. Usually used as the heating or cooling system thermostat.

Settlement- Shifts in a structure, usually caused by freeze-thaw cycles  underground.

Sewage  ejector- A pump used to 'lift' waste water to a gravity sanitary  sewer line. Usually used in basements and other locations which are  situated bellow the level of the side sewer.

Sewer  lateral- The portion of the sanitary sewer which connects the  interior waste water lines to the main sewer lines. The side sewer is  usually buried in several feet of soil and runs from the house to the  sewer line. It is usually 'owned' by the sewer utility, must be  maintained by the owner and may only be serviced by utility approved  contractors. Sometimes called side sewer.

Sewer stub- The junction at the municipal sewer system where the home's sewer line  is connected.

Sewer tap- The physical connection point where the home's sewer line connects to  the main municipal sewer line.

Shake- A wood roofing material, normally cedar or redwood. Produced by splitting a block of the wood along the grain line. Modern shakes are sometimes  machine sawn on one side. See shingle.

Shear block- Plywood that is face nailed to short (2 X 4's or 2 X 6's) wall studs  (above a door or window, for example). This is done to prevent the wall  from sliding and collapsing.

Sheathing,  sheeting- The structural wood panel covering, usually OSB or  plywood, used over studs, floor joists or rafters/trusses of a  structure.

Shed roof- A roof containing only one sloping plane.

Sheet metal work- All components of a house employing sheet metal, such as  flashing, gutters, and downspouts.

Sheet metal duct work- The heating system. Usually round or rectangular metal  pipes and sheet metal (for Return Air) and installed for distributing  warm (or cold) air from the furnace to rooms in the home.

Sheet rock- Drywall-Wall board or gypsum- A manufactured panel made out of  gypsum plaster and encased in a thin cardboard. Usually 1/2" thick and  4' x 8' or 4' x 12' in size. The 'joint compound'. 'Green board' type  drywall has a greater resistance to moisture than regular (white)  plasterboard and is used in bathrooms and other "wet areas".

Shim- A small piece of scrap lumber or shingle, usually wedge shaped, which  when forced behind a furring strip or framing member forces it into  position. Also used when installing doors and placed between the door  jamb legs and 2 X 4 door trimmers. Metal shims are wafer 1 1/2" X 2"  sheet metal of various thickness' used to fill gaps in wood framing  members, especially at bearing point locations.

Shingles- Roof covering of asphalt. asbestos, wood, tile, slate, or other  material cut to stock lengths, widths, and thickness'.

Shingles,  siding- Various kinds of shingles, used over sheathing for exterior  wall covering of a structure.

Short  circuit- A situation that occurs when hot and neutral wires come in  contact with each other. Fuses and circuit breakers protect against fire that could result from a short.

Shutter- Usually lightweight louvered decorative frames in the form of doors  located on the sides of a window. Some shutters are made to close over  the window for protection.

Side sewer- The portion of the sanitary sewer which connects the interior waste  water lines to the main sewer lines. The side sewer is usually buried in several feet of soil and runs from the house to the sewer line. It is  usually 'owned' by the sewer utility, must be maintained by the owner  and may only be serviced by utility approved contractors. Sometimes  called sewer lateral.

Siding- The finished exterior covering of the outside walls of a frame  building.

Siding,  (lap siding)- Slightly wedge-shaped boards used as horizontal siding in a lapped pattern over the exterior sheathing. Varies in butt  thickness from ½ to ¾ inch and in widths up to 12".

Sill-  (1) The 2 X 4 or 2 X 6 wood plate framing member that lays flat against  and bolted to the foundation wall (with anchor bolts) and upon which the floor joists are installed. Normally the sill plate is treated lumber.  (2) The member forming the lower side of an opening, as a door sill or  window sill.

Sill cock- An exterior water faucet (hose bib).

Sill plate  (mudsill)- Bottom horizontal member of an exterior wall frame which  rests on top a foundation, sometimes called mudsill. Also sole plate,  bottom member of an interior wall frame.

Sill seal- Fiberglass or foam insulation installed between the foundation wall and sill (wood) plate. Designed to seal any cracks or gaps.

Single hung window- A window with one vertically sliding sash or window vent.

Skylight- A more or less horizontal window located on the roof of a building.

Slab,  concrete- Concrete pavement, i.e. driveways, garages, and basement  floors.

Slab, door- A rectangular door without hinges or frame.

Slab on  grade- A type of foundation with a concrete floor which is placed  directly on the soil. The edge of the slab is usually thicker and acts  as the footing for the walls.

Slag-  Concrete cement that sometimes covers the vertical face of the  foundation void material.

Sleeper- Usually, a wood member embedded in concrete, as in a floor, that serves to support and to fasten the subfloor or flooring.

Sleeve(s)- Pipe installed under the concrete driveway or sidewalk, and that will  be used later to run sprinkler pipe or low voltage wire.

Slope-  The incline angle of a roof surface, given as a ratio of the rise (in  inches) to the run (in feet). See also pitch.

Slump-  The "wetness" of concrete. A 3 inch slump is dryer and stiffer than a 5  inch slump.

Soffit- The area below the eaves and overhangs. The underside where the roof  overhangs the walls. Usually the underside of an overhanging cornice.

Soil pipe- A large pipe that carries liquid and solid wastes to a sewer or septic  tank.

Soil stack- A plumbing vent pipe that penetrates the roof.

Sole plate- The bottom, horizontal framing member of a wall that's attached to the  floor sheeting and vertical wall studs.

Solid  bridging- A solid member placed between adjacent floor joists near  the center of the span to prevent joists or rafters from twisting.

Sonotube- Round, large cardboard tubes designed to hold wet concrete in place  until it hardens.

Sound  attenuation- Sound proofing a wall or subfloor, generally with  fiberglass insulation.

Space heat- Heat supplied to the living space, for example, to a room or the living area of a building.

Spacing- The distance between individual members or shingles in building  construction.

Span- The clear distance that a framing member carries a load without support  between structural supports. The horizontal distance from eaves to  eaves.

Spec home- A house built before it is sold. The builder speculates that he can  sell it at a profit.

Specifications or Specs- A narrative list of materials, methods, model numbers,  colors, allowances, and other details which supplement the information  contained in the blue prints. Written elaboration in specific detail  about construction materials and methods. Written to supplement working  drawings.

Splash  block- Portable concrete (or vinyl) channel generally placed beneath an exterior sill cock (water faucet) or downspout in order to receive  roof drainage from downspouts and to divert it away from the building.

Square- A unit of measure-100 square feet-usually applied to roofing and siding material. Also, a situation that exists when two elements are at right  angles to each other. Also a tool for checking this.

Square-tab  shingles- Shingles on which tabs are all the same size and exposure.

Squeegie- Fine pea gravel used to grade a floor (normally before concrete is  placed).

Stack  (trusses)- To position trusses on the walls in their correct  location.

Standard  practices of the trade(s)- One of the more common basic and minimum  construction standards. This is another way of saying that the work  should be done in the way it is normally done by the average  professional in the field.

Starter  strip- Asphalt roofing applied at the eaves that provides protection by filling in the spaces under the cutouts and joints of the first  course of shingles.

Stair  carriage or stringer- Supporting member for stair treads. Usually a 2 X 12 inch plank notched to receive the treads; sometimes called a  "rough horse."

Stair  landing- A platform between flights of stairs or at the termination  of a flight of stairs. Often used when stairs change direction. Normally no less than 3 ft. X 3 ft. square.

Stair rise- The vertical distance from stair tread to stair tread (and not to  exceed 7 ½").

Static vent- A vent that does not include a fan.

STC (Sound  Transmission Class)- The measure of sound stopping of ordinary  noise.

Steel  inspection- A municipal and/or engineers inspection of the concrete  foundation wall, conducted before concrete is poured into the foundation panels. Done to insure that the rebar (reinforcing bar), rebar nets,  void material, beam pocket plates, and basement window bucks are  installed and wrapped with rebar and complies with the foundation plan.

Step  flashing- Flashing application method used where a vertical surface  meets a sloping roof plane. 6" X 6" galvanized metal bent at a 90 degree angle, and installed beneath siding and over the top of shingles. Each  piece overlaps the one beneath it the entire length of the sloping roof  (step by step).

Stick built- A house built without prefabricated parts. Also called conventional  building.

Stile-  An upright framing member in a panel door.

Stool-  The flat molding fitted over the window sill between jambs and  contacting the bottom rail of the lower sash.  Also another name for  toilet.

Stop box- Normally a cast iron pipe with a lid (@ 5" in diameter) that is placed  vertically into the ground, situated near the water tap in the yard, and where a water cut-off valve to the home is located (underground). A  long pole with a special end is inserted into the curb stop to turn  off/on the water.

Stop Order- A formal, written notification to a contractor to discontinue some or  all work on a project for reasons such as safety violations, defective  materials or workmanship, or cancellation of the contract.

Stops-  Moldings along the inner edges of a door or window frame. Also valves  used to shut off water to a fixture.

Stop valve- A device installed in a water supply line, usually near a fixture, that permits an individual to shut off the water supply to one fixture  without interrupting service to the rest of the system.

Storm sash  or storm window-. An extra window usually placed outside of an  existing one, as additional protection against cold weather.

Storm sewer- A sewer system designed to collect storm water and is separated from  the waste water system.

Story-  That part of a building between any floor or between the floor and roof.

Strike- The plate on a door frame that engages a latch or dead bolt.

String,  stringer- A timber or other support for cross members in floors or  ceilings. In stairs, the supporting member for stair treads. Usually a 2 X 12 inch plank notched to receive the treads

Strip  flooring- Wood flooring consisting of narrow, matched strips.

Structural  floor- A framed lumber floor that is installed as a basement floor instead of concrete. This is done on very expansive soils.

Stub,  stubbed- To push through.

Stucco- Refers to an outside plaster finish made with Portland cement as its  base.

Stud- A vertical wood framing member, also referred to as a wall stud, attached to the horizontal sole plate below and the top plate above. Normally 2 X 4's or 2 X 6's, 8' long (sometimes 92 5/8"). One of a series of wood or metal vertical structural members placed as supporting elements in  walls and partitions.

Stud  framing- A building method that distributes structural loads to each of a series of relatively lightweight studs. Contrasts with  post-and-beam.

Stud shoe- A metal, structural bracket that reinforces a vertical stud. Used on an outside bearing wall where holes are drilled to accommodate a plumbing  waste line.

Subfloor- The framing components of a floor to include the sill plate, floor  joists, and deck sheeting over which a finish floor is to be laid.

Sump-  Pit or large plastic bucket/barrel inside the home designed to collect  ground water from a perimeter drain system.

Sump pump- A submersible pump in a sump pit that pumps any excess ground water to  the outside of the home.

Suspended  ceiling- A ceiling system supported by hanging it from the overhead  structural framing.

Sway brace- Metal straps or wood blocks installed diagonally on the inside of a  wall from bottom to top plate, to prevent the wall from twisting,  racking, or falling over "domino" fashion.

Switch- A device that completes or disconnects an electrical circuit.

Back To Top

T & G,  tongue and groove- A joint made by a tongue (a rib on one edge of a  board) that fits into a corresponding groove in the edge of another  board to make a tight flush joint. Typically, the subfloor plywood is T  & G.

Tab -  The exposed portion of strip shingles defined by cutouts.

Tail beam- A relatively short beam or joist supported in a wall on one end and by a header at the other.

Take off- The material necessary to complete a job.

Taping- The process of covering drywall joints with paper tape and joint  compound.

T bar-  Ribbed, "T" shaped bars with a flat metal plate at the bottom  that are driven into the earth. Normally used chain link fence poles,  and to mark locations of a water meter pit.

Teco-  Metal straps that are nailed and secure the roof rafters and trusses to  the top horizontal wall plate. Sometimes called a hurricane clip.

Tee- A  "T" shaped plumbing fitting.

Tempered- Strengthened. Tempered glass will not shatter nor create shards, but  will "pelletize" like an automobile window. Required in tub and shower  enclosures and locations, entry door glass and sidelight glass, and in a windows when the window sill is less than 16" to the floor.

Termites- Wood eating insects that superficially resemble ants in size and  general appearance, and live in colonies.

Termite  shield- A shield, usually of galvanized metal, placed in or on a  foundation wall or around pipes to prevent the passage of termites.

Terra cotta- A ceramic material molded into masonry units.

Thermoply - Exterior laminated sheathing nailed to the exterior side of the exterior walls. Normally ¼ " thick, 4 X 8 or 4 x 10 sheets with an  aluminumized surface.

Thermostat- A device which relegates the temperature of a room or building by  switching heating or cooling equipment on or off.

Three-dimensional shingles- Laminated shingles. Shingles that have added  dimensionality because of extra layers or tabs, giving a shake-like  appearance. May also be called "architectural shingles".

Threshold- The bottom metal or wood plate of an exterior door frame. Generally  they are adjustable to keep a tight fit with the door slab.

Time and  materials contract- A construction contract which specifies a price  for different elements of the work such as cost per hour of labor,  overhead, profit, etc. A contract which may not have a maximum price, or may state a 'price not to exceed'.

Tinner- Another name for the heating contractor.

Tip up- The downspout extension that directs water (from the home's gutter  system) away from the home. They typically swing up when mowing the  lawn, etc.

Title-  Evidence (usually in the form of a certificate or deed) of a person's  legal right to ownership of a property.

TJI or TJ- Manufactured structural building component resembling the letter "I". Used as floor joists and rafters. I-joists include two key parts: flanges and webs. The flange or from of the I joist may be made  of laminated veneer lumber or dimensional lumber, usually formed into a 1½" width. The web or center of the I-joist is commonly made of  plywood or oriented strand board (OSB). Large holes can be cut in the  web to accommodate duct work and plumbing waste lines. I-joists are  available in lengths up to 60'' long.

Toenailing- To drive a nail in at a slant. Method used to secure floor joists to  the plate.

Top chord- The upper or top member of a truss.

Top plate- Top horizontal member of a frame wall supporting ceiling joists,  rafters, or other members.

Transmitter (garage door)- The small, push button device that causes the garage door to open or close.

Trap- A plumbing fitting that holds water to prevent air, gas, and vermin from  backing up into a fixture.

Tread-  The walking surface board in a stairway on which the foot is placed.

Treated  lumber- A wood product which has been impregnated with chemical  pesticides such as CCA (Chromated Copper Arsenate) to reduce damage from wood rot or insects. Often used for the portions of a structure which  are likely to be in contact with soil and water. Wood may also be  treated with a fire retardant.

Trim  (plumbing, heating, electrical)- The work that the "mechanical"  contractors perform to finish their respective aspects of work, and when the home is nearing completion and occupancy.

Trim-  Interior- The finish materials in a building, such as moldings  applied around openings (window trim, door trim) or at the floor and  ceiling of rooms (baseboard, cornice, and other moldings). Also, the  physical work of installing interior doors and interior woodwork, to  include all handrails, guardrails, stair way balustrades, mantles, light boxes, base, door casings, cabinets, countertops, shelves, window sills and aprons, etc.Exterior- The finish materials on the exterior a building, such as moldings applied around openings (window trim, door  trim), siding, windows, exterior doors, attic vents, crawl space vents,  shutters, etc. Also, the physical work of installing these materials

Trimmer- The vertical stud that supports a header at a door, window, or other  opening.

Truss-  An engineered and manufactured roof support member with "zig-zag"  framing members. Does the same job as a rafter but is designed to have a longer span than a rafter.

Tub trap- Curved, "U" shaped section of a bath tub drain pipe that holds a water seal to prevent sewer gasses from entering the home through tubs  water drain.

Turnkey- A term used when the subcontractor provides all materials (and labor)  for a job.

Turpentine- A petroleum, volatile oil used as a thinner in paints and as a solvent  in varnishes

Back To Top

UL  (Underwriters' Laboratories)- An independent testing agency that  checks electrical devices and other components for possible safety  hazards.

Undercoat- A coating applied prior to the finishing or top coats of a paint job.  It may be the first of two or the second of three coats. Sometimes  called the Prime coat.

Underground plumbing- The plumbing drain and waste lines that are installed  beneath a basement floor.

Underlayment- A ¼" material placed over the subfloor plywood sheeting and under  finish coverings, such as vinyl flooring, to provide a smooth, even  surface. Also a secondary roofing layer that is waterproof or  water-resistant, installed on the roof deck and beneath shingles or  other roof-finishing layer.

Union- A plumbing fitting that joins pipes end-to-end so they can be dismantled.

Utility  easement- The area of the earth that has electric, gas, or telephone lines. These areas may be owned by the homeowner, but the utility  company has the legal right to enter the area as necessary to repair or  service the lines.

Back To Top

Valley- The "V" shaped area of a roof where two sloping roofs meet.  Water drains off the roof at the valleys.

Valley  flashing- Sheet metal that lays in the "V" area of a roof valley.

Valuation- An inspection carried out for the benefit of the mortgage lender to  ascertain if a property is a good security for a loan.

Valuation  fee- The fee paid by the prospective borrower for the lender's  inspection of the property. Normally paid upon loan application.

Vapor  barrier- A building product installed on exterior walls and ceilings under the drywall and on the warm side of the insulation. It is used to retard the movement of water vapor into walls and prevent condensation  within them. Normally, polyethylene plastic sheeting is used.

Variable  rate- An interest rate that will vary over the term of the loan.

Veneer- Extremely thin sheets of wood. Also a thin slice of wood or brick or  stone covering a framed wall.

Vent- A pipe or duct which allows the flow of air and gasses to the outside.  Also, another word for the moving glass part of a window sash, i.e.  window vent.

Vermiculite- A mineral used as bulk insulation and also as aggregate in insulating  and acoustical plaster and in insulating concrete floors.

Veterans  Administration (VA)- A federal agency that insures mortgage loans  with very liberal down payment requirements for honorably discharged  veterans and their surviving spouses.

Visqueen- A 4 mil or 6 mil plastic sheeting.

Void-  Cardboard rectangular boxes that are installed between the earth  (between caissons) and the concrete foundation wall. Used when expansive soils are present.

Voltage- A measure of electrical potential. Most homes are wired with 110 and  220 volt lines. The 110 volt power is used for lighting and most of the  other circuits. The 220 volt power is usually used for the kitchen  range, hot water heater and dryer.

Back To Top

Wafer board- A manufactured wood panel made out of 1"- 2" wood chips and glue. Often used as a substitute for plywood in the exterior wall and roof  sheathing.

Walk-Through- A final inspection of a home before "Closing" to look for and document  problems that need to be corrected.

Wall out- When a painter pray paints the interior of a home.

Warping- Any distortion in a material.

Warranty- In construction there are two general types of warranties. One is  provided by the manufacturer of a product such as roofing material or an appliance. The second is a warranty for the labor. For example, a  roofing contract may include a 20 year material warranty and a 5 year  labor warranty. Many new homebuilders provide a one year warranty. Any  major issue found during the first year should be communicated to the  builder immediately. Small items can be saved up and presented to the  builder for correction periodically through the first year after  closing.

Waste pipe  and vent- Plumbing plastic pipe that carries waste water to the  municipal sewage system.

Water board- Water resistant drywall to be used in tub and shower locations.  Normally green or blue colored

Water  closet- Another name for toilet.

Water meter pit (or vault)- The box /cast iron bonnet and concrete rings that  contains the water meter.

Water-repellent preservative- A liquid applied to wood to give the wood water  repellant properties

Water table- The location of the underground water, and the vertical distance from  the surface of the earth to this underground water.

Water tap- The connection point where the home water line connects to the main  municipal water system.

W C- An abbreviation for water closet (toilet).

Weatherization- Work on a building exterior in order to reduce energy consumption for  heating or cooling.  Work involving adding insulation, installing storm windows and doors, caulking cracks and putting on weather-stripping.

Weatherstrip- Narrow sections of thin metal or other material installed to prevent  the infiltration of air and moisture around windows and doors.

Weep holes- Small holes in storm window frames that allow moisture to escape.

Whole house fan- A fan designed to move air through and out of a home and  normally installed in the ceiling.

Wind  bracing- Metal straps or wood blocks installed diagonally on the  inside of a wall from bottom to top plate, to prevent the wall from  twisting, racking, or falling over "domino" fashion.

Window buck- Square or rectangular box that is installed within a concrete  foundation or block wall. A window will eventually be installed in this  "buck" during the siding stage of construction

Window  frame- The stationary part of a window unit; window sash fits into  the window frame.

Window sash- The operating or movable part of a window; the sash is made of window  panes and their border.

Wire nut- Plastic device used to connect bare wires together.

Wonderboard - A panel made out of concrete and fiberglass usually used as a  ceramic tile backing material. Commonly used on bathtub decks.

Wrapped  drywall- Areas that get complete drywall covering, as in the doorway openings of bifold and bipass closet doors.

Back To Top

Y- A  "Y" shaped plumbing fitting.

Yard of  concrete- One cubic yard of concrete is 3' X 3' X 3' in volume, or  27 cubic feet. One cubic yard of concrete will pour 80 square feet of 3½" sidewalk or basement/garage floor.

Yoke-  The location where a home's water meter is sometimes installed between  two copper pipes, and located in the water meter pit in the yard.

Back To Top

Z-bar  flashing- Bent, galvanized metal flashing that's installed above a  horizontal trim board of an exterior window, door, or brick run. It  prevents water from getting behind the trim/brick and into the home.

Zone-  The section of a building that is served by one heating or cooling loop  because it has noticeably distinct heating or cooling needs. Also, the  section of property that will be watered from a lawn sprinkler system.

Zone valve- A device, usually placed near the heater or cooler, which controls the  flow of water or steam to parts of the building; it is controlled by a  zone thermostat.

Zoning- A governmental process and specification which limits the use of a  property e.g. single family use, high rise residential use, industrial  use, etc. Zoning laws may limit where you can locate a structure. Also  see building codes.

Back To Top